14 Jan 2025 · Huahui Fire technical team

UN 38.3 tests for the transport of lithium batteries

UN 38.3 is Section 38.3 of the UN Manual of Tests and Criteria for the transport of dangerous goods. Before lithium batteries can be shipped they must pass altitude simulation, thermal, vibration, shock, external short circuit, impact/crush, overcharge and forced discharge tests. This article sets out each test and the pass criteria.

What is UN 38.3 testing?

UN 38.3 refers to Section 38.3 of the UN Manual of Tests and Criteria for the transport of dangerous goods, drawn up by the United Nations specifically for dangerous goods transport. It requires lithium batteries to pass high/low temperature cycling, vibration, shock, external short circuit, impact, overcharge and forced discharge tests before they are transported, to ensure they can be shipped safely. If the lithium batteries are not installed in equipment and each package contains more than 24 cells or 12 batteries, they must also pass a 1.2 m free-drop test.

Why UN 38.3 testing is needed

A UN 38.3 report is a battery safety performance test report. Each battery model undergoes a full set of safety tests against Chinese and international standards, helping battery manufacturers assure the quality and safety of their products, meet the relevant standards and improve their ability to export.

  1. UN 38.3 testing is mandatory to ensure that lithium batteries can be transported safely by air, sea and land.

  2. The Civil Aviation Administration of China has issued Specifications for the air transport of lithium batteries to airlines. They state explicitly that lithium batteries must be tested to UN 38.3 by a CNAS-accredited laboratory before transport by air or sea, and that airlines may accept lithium batteries for carriage only on receipt of a passing UN 38.3 report and a transport classification certificate.

UN 38.3 test items

Altitude simulation

Purpose: to simulate air transport under low-pressure conditions, at a pressure of ≤ 11.6 kPa and a temperature of 20 ± 5 °C.

Procedure: test cells and batteries are stored for at least 6 hours at a pressure of 11.6 kPa or less and an ambient temperature of (20 ± 5) °C.

Thermal test / thermal shock

Purpose: to assess cell and battery seal integrity and internal electrical connections, using rapid and extreme temperature changes.

Procedure:

(1) Store at a test temperature of (72 ± 2) °C for at least 6 hours, then at a test temperature of (−40 ± 2) °C for at least 6 hours.

(2) The maximum time interval between the two extreme test temperatures is 30 minutes; repeat 10 times.

(3) Store for 24 hours at an ambient temperature of (20 ± 5) °C.

(4) For large cells and batteries, the exposure to each extreme test temperature should be at least 12 hours.

Vibration

Purpose: to simulate vibration during transport.

Procedure:

(1) Cells and batteries are firmly secured to the platform of the vibration machine, but not so tightly that the cells are distorted and the vibration is not faithfully transmitted.

(2) The vibration is a sinusoidal waveform with a logarithmic sweep from 7 Hz to 200 Hz and back to 7 Hz, traversed in 15 minutes.

(3) This cycle is repeated 12 times in each of three mutually perpendicular mounting orientations of the cell, a total of 3 hours. One of the directions of vibration must be perpendicular to the terminal face.

(4) The logarithmic frequency sweep differs for cells and batteries with a gross mass under 12 kg (cells and small batteries) and for large batteries over 12 kg.

Shock

Purpose: to assess the robustness of cells and batteries against cumulative shock.

Procedure:

(1) Test cells and batteries are secured to the test machine by a rigid mount that supports all mounting surfaces of each test battery.

(2) Each cell is subjected to a half-sine shock with a peak acceleration of 150 gn and a pulse duration of 6 ms. Large cells are subjected to a half-sine shock with a peak acceleration of 50 gn and a pulse duration of 11 ms. For batteries, the peak acceleration of the half-sine shock depends on the mass of the battery; the pulse duration is 6 ms for small batteries and 11 ms for large batteries.

(3) Each cell or battery is subjected to three shocks in the positive direction, followed by three shocks in the negative direction, in each of three mutually perpendicular mounting orientations, a total of 18 shocks.

External short circuit

Purpose: to simulate an external short circuit.

Procedure:

(1) The cell or battery to be tested is heated for long enough to reach a homogeneous, stabilised temperature of (57 ± 4) °C measured on the external case. This time depends on the size and design of the cell or battery and should be assessed and recorded. If this assessment is not possible, the exposure time should be at least 6 hours for small cells and small batteries and at least 12 hours for large cells and large batteries.

(2) The cell or battery at (57 ± 4) °C is then subjected to a short circuit with a total external resistance of less than 0.1 Ω.

(3) The short circuit is continued for at least 1 hour after the external case temperature of the cell or battery has returned to (57 ± 4) °C, or, for large batteries, until the case temperature has fallen by half of the maximum temperature rise observed during the test and remains below that value.

(4) The temperature during the short circuit and cooling phases should be at least equal to the ambient temperature.

Impact / crush

Purpose: to simulate mechanical abuse, such as impact or crush, that may cause an internal short circuit (cells only).

Procedure:

Impact: applies to cylindrical cells with a (design) diameter of 18.0 mm or more.

(1) The test cell or component cell is placed on a flat, smooth surface. A Type 316 stainless steel bar, 15.8 mm ± 0.1 mm in diameter and at least 6 cm long, or as long as the longest dimension of the cell, whichever is greater, is placed across the centre of the specimen.

(2) A 9.1 kg ± 0.1 kg mass is dropped from a height of 61 cm ± 2.5 cm onto the intersection of the bar and the specimen, controlled by a near-frictionless vertical track or tube offering minimal resistance to the falling mass. The track or tube guides the mass so that it falls at 90° to the horizontal supporting surface.

(3) The specimen is impacted with its longitudinal axis parallel to the flat surface and perpendicular to the longitudinal axis of the 15.8 mm ± 0.1 mm diameter curved surface lying across its centre. Each specimen is subjected to one impact only.

Crush: applies to prismatic, pouch, coin/button cells and cylindrical cells less than 18.0 mm in diameter.

(1) The cell or component cell is crushed between two flat surfaces, with the crushing force increasing gradually at a speed of about 1.5 cm/s at the first point of contact. Crushing continues until one of the following three occurs:

(a) the applied force reaches 13 kN ± 0.78 kN;

(b) the cell voltage drops by at least 100 mV; or

(c) the cell is deformed by 50 % or more of its original thickness.

(2) Once the maximum force has been reached, the voltage has dropped by 100 mV or more, or the cell has been deformed by at least 50 % of its original thickness, the pressure is released.

(3) Prismatic or pouch cells are crushed on their widest face. Button/coin cells are crushed on their flat surfaces. Cylindrical cells are crushed perpendicular to their longitudinal axis.

(4) Each cell or component cell is subjected to one crush only, and the specimen is observed for a further 6 hours. The test is carried out on cells or component cells that have not previously been subjected to other tests.

Overcharge

Purpose: to assess the ability of a rechargeable battery or single-cell rechargeable battery to withstand an overcharge condition.

Procedure:

(1) The charge current is twice the manufacturer's recommended maximum continuous charge current. The minimum test voltage is as follows:

(A) where the manufacturer's recommended charge voltage is not more than 18 V, the minimum test voltage is the lesser of twice the maximum charge voltage of the battery or 22 V;

(B) where the manufacturer's recommended charge voltage is more than 18 V, the minimum test voltage is 1.2 times the maximum charge voltage.

(2) The test is carried out at ambient temperature for 24 hours.

Forced discharge

Purpose: to assess the ability of a primary or rechargeable cell to withstand a forced discharge condition.

Procedure: each cell is force-discharged at ambient temperature by connecting it in series with a 12 V DC power supply, at an initial current equal to the maximum discharge current specified by the manufacturer. The specified discharge current is obtained by connecting a resistive load of appropriate size and rating in series with the test cell. Each cell is force-discharged for a time (in hours) equal to its rated capacity divided by the initial test current (in amperes).

Additional: 1.2 m drop (packaged)

The packaged lithium batteries, at 20 ± 5 °C, are dropped from 1,200 mm (measured to the lowest point of the battery) onto a hardwood board 18–20 mm thick laid on a concrete floor. The test samples must not catch fire or explode during or after the test.

Pass criteria

According to section 38.3 of the UN Manual of Tests and Criteria, Rev. 7:

(1) Tests T.1 to T.4: no leakage, no venting, no disassembly, no rupture and no fire, and the open-circuit voltage after the test is at least 90 % of the voltage before it (the voltage requirement does not apply to fully discharged specimens).

(2) Tests T.5 and T.6: the external case temperature does not exceed 170 °C, and there is no disassembly, no rupture and no fire during the test and within 6 hours after it.

(3) Tests T.7 and T.8: no disassembly and no fire during the test and within 7 days after it.

(4) In the 1.2 m drop, one drop in each of the six directions (positive and negative X, Y and Z) results in no leakage, disassembly, burning, explosion or damage.

If a cell or battery type does not meet one or more of the test requirements, steps should be taken to correct the deficiency that caused the failure, and the cell or battery type should then be retested.

First published on our WeChat channel: read the original

Talk to an engineer

Tell us what you need to test

Describe the product, target market and standards. An engineer will get back to you shortly.